Show Details

 

 

What are your thoughts about How to Install a Bathtub Yourself?

Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is readily obtainable, the project can relocate quickly; if you need to open up a wall to remove the old tub and also place the brand-new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub and also set in the new one. Make certain you have actually certified yourself for the task and also are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed project, it is far better to think about utilizing one before you start. Chances are you may require an expert plumber to make tube connections.
This short article will certainly aid you install a new tub in your shower room if you have actually already acquired a brand-new tub and don't need to transform the setup of your previous supply of water pipes.
Your devices and also material list need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

To start with, the supporting frame provided with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.

 

 

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Installing the Tub

Using the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Activate the water supply as well as examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait up until the tub has actually been made use of at least once as this will certainly resolve it right into its final position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Tub

In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall between the bath and the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our piece on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to browse our posting. Liked our post? Please share it. Let somebody else locate it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.

Free Estimates

Click Here

 

They are making several great annotation on 3 Signs You Need Toilet Repair in general in this article underneath.

Plumbing concerns at residence do not get worse than a faulty bathroom. Picture doing your company in the restroom, as well as the commode won't purge.
There are numerous indicators that your commode could be defective, and we will quickly consider these indications and also events that, when seen, you require to speak to a specialist plumbing service to either fix the commode or reinstall it.

 

Effects of Faulty Toilets

Malfunctioning toilets can hamper your wellness and also cause a boost in utility bills. They can develop area for molds, bacteria, as well as various other unpleasant organisms to hide in the shower room. Faulty commodes can additionally enhance the risk of flooding and clogging. Actually, a few of these signs are difficult to map or spot, as well as in many cases, you will certainly need an expert to find as well as repair them.
Bathrooms don't last for life, and like every other thing, they can outlast their purposes as well as require a replacement. There are some symptoms and signs that go along with a faulty commode, as well as your capacity to keep in mind of them on time as well as hire experts can conserve you a great deal of dangers.

 

1. Split in the Tank

The first indicator that your Tank might be split is the visibility of water puddles near the base of your commode. Splits in the Tank are often tough to spot, particularly if it's just a small one somewhere below the waterline. When you notice water settling on your bathroom base, it is most likely indicative that your Tank has fractured, as well as you require to include the plumbers to spot the place and also either fix it or change it.

 

2. Leaky Commode

Sadly, the only means you might recognize you have a dripping toilet is when the water bills keep increasing. Dripping toilets are horrible due to the fact that they can cause lots of damages in the residence, consisting of developing a space for molds and also molds, spoiling the flooring, as well as if the damaged bathroom remains in an upstairs bathroom, it can create problems to spaces beneath it. The best option for a leaky toilet, particularly if it's old, is to change it. Get in touch with an expert to take a look at it as well as let them get the job done.

 

3. Clogs

Obstructing bathrooms happen quite on a regular basis, and also every person experiences it every now and then. If your bathroom quits extra frequently, you might require to have it checked. If you have children in your home, the chances are high that they might have tried purging playthings or textiles down the tubes at some time. A clogged commode postures a considerable hazard to the sewage, specifically when materials other than tissue papers and also human waste are purged down there. While a plunger can do the majority of the unclogging, you must call a specialist if you notice that it happens very frequently. Your commode could need more than just a plunging to return in good shape.

 

4. Weak Flush

If your commode does not allow a whole lot of water down to flush everything, there might be an issue. Having to flush your toilet more than once or two times is tiring and affects the costs. In some cases, the water in the toilet bowl is constantly running, and there is not enough to flush when you require to.

 

Let the Pros In

These are some of one of the most usual root causes of a damaged toilet, and now that you recognize, you certainly have an idea why there is always water at the base of your toilet or why it does not flush properly.
Swiftly call an expert when you see these indications. If you reside in Pittsburgh, our experienced plumbings can help salvage your commode as well as get it back in great working problems.
Some of these mistakes are indicative of a demand to change your bathroom. We also manage toilet installments as well as substitutes. With our many years of experience in the field, our solutions are irresistible.
Imagine doing your service in the restroom, and also the toilet will not flush. Leaking commodes are awful due to the fact that they can trigger lots of damages in the home, consisting of creating a space for mildews and also molds, wrecking the flooring, as well as if the faulty toilet is in an upstairs washroom, it can cause troubles to spaces underneath it. If your toilet does not let a whole lot of water down to purge whatever, there may be an issue. Having to purge your toilet more than as soon as or twice is strenuous and also affects the expenses. In some instances, the water in the toilet bowl is regularly running, and also there is not enough to purge when you require to.

 

Possible Reasons Your Toilet is Leaking

 

A leaking toilet is one of the most inconvenient and costly plumbing problems that homeowners face. A common tell-tale sign of a leaking toilet is the formation of a puddle near the toilet or moisture spontaneously forming on the toilet’s tank. Another tell-tale sign is a toilet that keeps running or flushing even when it isn’t used. Under normal circumstances, about 27% of water usage comes from toilet flushing. Therefore, a running toilet due to leakage can have a major impact on your water bill if left unfixed.

Needless to say, toilet leaks, whatever the cause, need to be fixed ASAP. If you notice that the toilet leak is rapidly progressing or if you have a plumbing emergency on your hands, reach out to our plumbing emergency experts who are available round the clock and try to shut off the water supply to your toilet while waiting.

However, if you have a minor leak happening with your toilet, you may want to figure out the root cause of it and decide your next steps from there. Well, you’re in the right place! This article covers the top 5 common reasons why toilets leak and how to spot them.

 

Leaking Supply Line

 

The supply line is the part of the toilet that supplies water into the tank of the toilet for flushing. The supply line is typically found outside of the toilet and it connects to two points: the supply valve which is typically installed into the wall and to the toilet’s tank. These lines are usually made of either plastic, vinyl, or stainless steel. Problems can arise when the joints of the supply line become weak or loose due to either wear and tear or accidental physical impact. The solution to this problem is typically to replace the supply line altogether.

 

Broken Wax Seal

 

The wax seal is located under your toilet where it serves as an impermeable barrier to keep flushed water and sewage from leaking outside. Since this part is enclosed, the most common reason why it gets damaged is simple wear and tear. Replacing the wax seal is a complicated process that involves actually removing the whole toilet from its place. Out of all the causes listed here, this one involves the most risk and should not be considered for DIY. Slight mistakes in the process can leave you with even worse problems.

 

Damaged Toilet Tank

 

The toilet tank is a part we’re all familiar with. This holds all the water for flushing as well as the toilet’s flushing mechanisms. Over time, the toilet tank can sustain cracks because of age or physical impact. Fortunately, really small cracks won’t mean that you need to replace your toilet. These can be quickly remedied using a sealer. Larger cracks, however, may get worse and could mean that you need to replace your toilet.

 

Damaged Toilet Float

 

The toilet float is located inside the toilet tank and is the ball that you can see floating on top of the toilet tank’s water. This serves to trigger the mechanism for refilling the water in the toilet tank when water levels run low. When this part is damaged, the fill valve of the toilet tends to run continuously. The common cause of damage to this part is wear and tear or inappropriate handling.

https://www.plumbwize.ca/blog/5-reasons-your-toilet-is-leaking/

 

I was shown that editorial on 3 Signs You Need Toilet Repair through a good friend on another website. Make sure you take the opportunity to promote this content if you enjoyed reading it. I enjoy reading our article about 3 Signs You Need Toilet Repair.

Fast and effective, call!